Pick up more of your valuable hay

New Holland Rolabar® rakes let you feed cleaner hay and more of it. Offset wheels are set close to the basket, so tines follow the ground contour closely to pick up all the hay—but leave dirt behind.

In-line telescoping drive transfers power from the wheels to the reel through heat-treated gears. The universal gears are designed to take severe punishment, requiring only minimal lubrication and attention.

Height adjustment cranks permit adjustments to either side of the basket for proper ground clearance.

Crank arm locks prevent arms from changing positions over rough terrain.

Proven basket suspension provides a full range of settings. Tines tilt up for fluffy, fast-drying windrows or down for tight windrows.

Trip lever for gearbox clutch can be engaged from the tractor seat. No need to disconnect the drive each time you tow the rake (ground-drive models).

Dual-raking Models (Models 216 and 252 Rake Hitch)

Using two rakes instead of one cuts labor, fuel consumption and tractor time in half. Transport, operate and adjust two Rolabar rakes without leaving your tractor seat with the 252 rake hitch.

Rake hitch has a narrow 8 ft. 11 in. transport width.
Flexibility to rake two separate windrows, or combine two swaths or windrows into one.

Use with all New Holland rakes: 8 ft. 6 in. or 9 ft. 6 in. rakes, ground-drive or hydraulic-drive, right- or left-hand delivery, or in combination.

For the big-acreage haymaker, the 216 rakes up to 27 feet in one pass.

Unitized frame carries two 10 ft. 6 in. baskets that rake a path wide enough to combine two windrows from 16-ft. windrowers. Maintains constant windrow width, even in sharp turns.

Folds to a narrow ten feet for easy transport.

Change settings right from your tractor seat with the rake control box.

Easy-to-set frame and basket limit stops let you repeat your last frame setting each time you open the rake.
Rubber Dyna-tines provide long life. They are mounted individually and can be replaced easily and economically.

Superior basket suspension lifts tines over obstacles for cleaner raking and less tine failure.

High-volume raking with day-after-day durability

Offered in seven working widths from 17 ft. 5 in. (8 wheel) to 36 ft. (20 wheel), New Holland trailing wheel rakes offer important design advantages that help you move more hay and make bigger, fluffier windrows. And, these folding "V" rakes are built to handle the rigors of tough conditions and high-speed operation.

Select the model that’s right for your operation. HT152 standard rakes are designed for low- to mid-volume producers with smaller acreage, while HT154 deluxe rakes are designed for high-volume hay producers and large-acreage operations.

Reinforced, articulating main frame provides the needed durability to carry the extra load of wide raking settings. High-strength steel tubing (4 in. x 4 in.) is used for the construction of the main frame and each rake wheel frame for long life and dependable service. Components are bolted, not welded, for a stronger frame.
 
Ample 4 ft. 8 in. vertical clearance allows large, fluffy windrows to pass through without plugging.
  
Each 55-inch-diameter raking wheel provides a large surface area, using 40 equally spaced tines to gently pick up and move all of the crop to build fluffy, fast-drying windrows.

Robust 9/32 in. spring steel finger tines are designed for hard use day after day, and can be individually replaced if necessary.

Adjustable flotation spring for each raking wheel provides just the right amount of pressure to float over terrain without damaging fields or the finger tines. All flotation springs on each rake wheel frame are connected to a centralized adjustment crank screw that allows operators to quickly change flotation pressure for the entire assembly.

Standard mechanical ratchet windrow width adjustment allows you to change windrow width from 3 ft. to 5 ft. on the HT152 and from 3 ft. to 6 ft. on the HT154. An optional hydraulic kit on the HT154 lets you make changes on-the-go without leaving the tractor seat.

Hefty 3 3/4 in. hydraulic swing cylinders allow you to change between field position and transport from the comfort of your tractor seat. A swing cylinder lockout valve is standard on all rakes.

Compact 8 ft. 3 in.  transport width for all models allows for easy maneuvering on narrow roads and through gates.
 
Adjustable friction disc brakes on the caster wheels steady the wheels in the field and eliminate high-speed shimmy during road transport.

Regreasable rake wheel bearings as well as heavy-duty, regreasable nylon bushings in each rake wheel arm pivot provide long life and quiet, smooth operation.

Handy jack stand supports the hitch and tongue when not in use, and pivots into storage during field operation.

Adjustable clevis hitch can be easily changed to match tractor drawbar height.

Two hydraulic remote outlets are required—one for raising and lowering the raking wheel arm assemblies and one for swinging between transport and operating position. A third remote circuit is needed for the optional hydraulic windrow width adjustment.

Optional center wheel kit turns and moves the unraked center portion of the swath into the windrow, offsetting the hay from damp ground and exposing the underside of the swath for faster drying.

Optional two wheel conversion kit extends the raking width of selected New Holland trailing wheel rakes by installing an additional raking wheel to each rake frame.

Optional single side opening kit allows the operator to hydraulically extend only one side of the rake, for use when turning rain dampened windrows.